Chip Resistor Arrays
CR, CJ, CRA, CRB, CRC Series - Test Conditions
MECHANICAL CHARACTERISTICS
Item
Standard
Test Conditions
Resistor
Jumper
Resistor
Jumper
R/R
±(1%+0.05 ? ) max.
of the initial value
50m ? max.
Apply the load as shown:
Measure resistance during load application
millimeters (inches)
20
Terminal
Strength
Visual
No evidence of mechanical damage after loading
Bending in
10 seconds
R230
50
(0.787) (1.969)
± 2 (0.079)max
[ φ 5 (0.197)]
45 (1.772) 45 (1.772)
PC Board = Glass epoxy t = 1.60 (0.063)
Soldering
Heat
Resistance
R/R
Visual
±(1%+0.05 ? ) max.
of the initial value
No evidence of leaching
50m ? max.
Immerse into molten solder at 260±5°C for 10±1 sec.
Stabilize component at room temperature for 1 hr.
Measure resistance.
Solderability
Coverage ≥ 95% each termination end
Immerse in Rogin Flux for 2±0.5 sec. and in
SN62 solder at 235±5°C for 2±0.5 sec.
Anti-Vibration
Test
Solvent
Resistance
R/R
Visual
R/R
Visual
±(1%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
±(0.5%+0.05 ? ) max.
of the initial value
No evidence of mechanical damage
50m ? max.
50m ? max.
2 hrs. each in X, Y and Z axis. (TTL 6 hrs.) 10 to 55 Hz
sweep in 1 min. at 1.5mm amplitude.
Immerse in static state butyl acetate at 20°C to 25°C
for 30±5 sec.
Stabilize component at room temperature for 30 min.
then measure value.
ENVIRONMENTAL CHARACTERISTICS
Item
Standard
Test Conditions
Resistor
Jumper
Resistor
Jumper
Temperature
Cycle
Low
Temperature
Storage
High
Temperature
Storage
Moisture
Resistance
Life Test
Loading Life
in Moisture
R/R
Visual
R/R
Visual
R/R
Visual
R/R
Visual
R/R
Visual
R/R
Visual
±(1%+0.05 ? ) max.
of the initial value
No evidence of mechanical damage
±(2%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
±(3%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
±(3%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
±(3%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
±(3%+0.1 ? ) max.
of the initial value
No evidence of mechanical damage
50m ? max.
50m ? max.
50m ? max.
50m ? max.
50m ? max.
50m ? max.
(1) Run 5 cycles as follows: -55±3°C for 30 min.
125±3°C for 30 min. Room temp. for 10-15 min.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
-0
(1) Dwell in -55°C chamber without loading for 1000 +48
hrs.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
-0
(1) Dwell in 125°C chamber without loading for 1000 +48
hrs.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
(1) Dwell in temp.: 65°C RH90 to 95% RH chamber
-0
without loading for 1000 +48 hrs.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
(1) Temp.: 70±3°C Voltage: (rated voltage) on 90 min.
-0
off 30 min. Duration: 1000 +48 hrs.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
-0
(1) Temp.: 40±2°C RH: 90-95% Voltage Cycle: on 90
min. (rated voltage) off 30 min. Duration: 1000 +48 hrs.
(2) Stabilize component at room temperature for 1 hr.
then measure value.
10
相关PDF资料
CRE22F2PBBNE SWITCH ROCKER SPST 20A 125V
CS-018-114.285MHZ CRYSTAL 114.285 MHZ 18PF SMD
CS-11210-BT CABINET CHAMPION 6" X 12" X 8"
CS-11227-S CABINET DESKTOP SLIMCAB 17" X16"
CS302010 BOX STEEL 30X20X10" GREY
CS325-48.000MABJ-UT CRYSTAL 48.0000MHZ 18PF SMD
CS325S-27.000MEEQ-UT CRYSTAL 27MHZ 10PF SMD
CSA309-30.000MABJ-UB CRYSTAL 30.000 MHZ 18PF CYL
相关代理商/技术参数
CRC430J 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 43pF 2000V C0G 5% (15 X 5mm) Radial 9.5mm 125°C
CRC470J 制造商:CORNELL DUBILIER ELECTRONICS 功能描述:Cap Ceramic 47pF 2000V C0G 5% (15 X 5mm) Radial 9.5mm 125°C
CRC4A8E100JT 功能描述:电阻器网络与阵列 10 OHM CNVX SQ RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CRC4A8E101JT 功能描述:电阻器网络与阵列 100 OHM 5% CONVEX RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CRC4A8E103JT 功能描述:电阻器网络与阵列 10K OHM CNVX SQD RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CRC4A8E220JT 功能描述:电阻器网络与阵列 22 OHM CNVX SQD RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CRC4A8E270JT 功能描述:电阻器网络与阵列 27 OHM 5% CONVEX SQ RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel
CRC4A8E510JT 功能描述:电阻器网络与阵列 51 OHM 5% CONVEX SQ RoHS:否 制造商:Vishay/Thin Film 产品类型:Networks 电路类型:Divider 电阻器数量: 电阻数值:10 kOhms 容差:0.1 % 温度系数: 管脚数量:3 工作温度范围:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引线间隔: 端接类型:SMD/SMT 封装:Reel